INFORMATION
Overview
16voice phone fiber multiplexer is point to point fiber
transmitting equipment, which is designed on large scale integrated circuit,
realizes 1~4 E1 circuit, 1~4channels 10/100/1000M Ethernet, 16 channel voice (FXO/FXS) and 1~2
channel RS232. Its merits include complete warning function, high integration,
low consumption, stable performance and convenient usage. In the 16channel
voices, the FXS and FXO can be combinated freely, for example,8*FXS+8*FXO.
Feature
- Provides1~ 4 channel
E1/ G.703 for option;
- provides 1~4
channel 1000M (line)
Ethernet ports for option;
- provides 16
channel voice port, FXO and FXS for option;
- provides1~2
channel RS232, rate supports 300-15200 bps for option;
- Ethernet port
10/100/1000M,
full/half duplex auto-adaptable and supports VLAN;
- Ethernet port
supports AUTO-MDIX (twisted cable and straight cable auto-adaptable);
- 1-16 channel
voice connection, supports calling indication;
- Configuration:
point to point;
- Voice port
supports O port and S port, O port connects switch and S port connects user’s
phone;
- Optical interface
supports SC/FC interface and supports single fiber interface
- Power can support
DC48V or AC220V or AC+DC
16voice+4GE fiber multiplexer back panel picture
Optical interface
Optical
wavelength: single mode 1310nm/1550nm
Fiber: single
fiber or double fiber for option
Transmitting
consumption: -9dBm/-5dBm
Transmission
range: 0-50Km/120Km for option
Optical
interface: SC/FC
Receiving and
dispatching module: >-6dBm
Optical receiver
receiving sensitivity <-36 dBm (BER<10-11)
Fiber circuit
code: NRZ code
FXS:
Alarm voltage: 75V
Alarmf requency:
25HZ
2 line input impedance:
600Ω (hanging off)
Wastage: 40db
FXO:
Alarm detecting voltage:
35V
Alarm detecting frequency: 17HZ-60HZ
2 line input impedance:
600Ω (hanging off)
Wastage:
40db
10/100/1000M Base-T Ethernet Interface
Rate: 10/100/1000M, full/duplex auto-negotiation
Protocol: Support IEEE 802.3, IEEE 802.1Q
(VLAN)
MAC Address Entiries: 4096 Entiries
Total Memory Sizes: 64MBits SDRAM
Physical interface: RJ45, support
AUTO-MDIX
E1 Interface
Interface standard:
Conforms to G.703 standard
Interface rate: N×64Kbps, N:1～32
Vibration
characteristic: Satisfies G.742 and G.823 standard
Transmission
capacity: 1*E1
Clock type: internal-clock,
route clock
Connecter: BNC (75 Ω
Interface impedance:
75Ω(non- balanced)
RS232 port
Rate： 300－115.2Kbps auto-adaptable (Asynchronous)
Interface characteristic： satisfies
ITU-T V.24 standard
Connector：RJ45
Dimension
19inch 1U high rack mount 433mm(L)x238mm(W)x44mm(H)
Environment condition
Operating
temperature: 0C~+50 C
Storage
temperature: -20
C~+70 C
Relative
temperature:95% (uncondensed)
Power supply
working
voltage range wide, good
anti-disturb
and Isolation, work stable
option
I – DC-48V,range DC-36V~DC-72C
option
II – AC220V,range AC90V~AC260V
Power Consumption: <=3 Watts
Application:
FAQ:
Question1: Just to confirm again, can the voice phone fiber multiplexer equipment have the following specifications:
FXO Port
1. Ringing Voltage Range: -90V-140V rms
2. Voltage to AB Leg: Must be able to handle Exchange voltage of A-line -48V DC, B-line 0V DC.
FXS Port
Line Voltage A-B: -48V DC
Answer: Yes, the voice phone fiber multiplexer has the above specifications.
Question2: Is there VLAN dip switch built on the POTS telephone fiber multiplexer?
Answer: The fiber mux device has not DIP switch for VLAN setting. You configure the VLAN TAG by console management.
Question3: Can the FXS FXO over fibrt multiplexer be managed by SNMP?
Answer: Yes, the FXS/FXO fiber multiplexer support SNMP management.
Question4: Can the Fiber Multiplexer be configured as 4Voice+4ETH+4RS232 with SNMP? If can, does the device have VLAN dip switch?
Answer: Yes, the Fiber Multiplexer can be configured as 4Voice+4ETH+4RS232 with SNMP. But the device doesn't have VLAN dip switch. VLAN cannot be set through SNMP, only can be set through console management.
Related Links:
Can POTs Fiber Multiplexer support DSL Transmission?
Ordering information
Related Products
