INFORMATION
Functions
8E1 to optical ethernet (100Base-FX) converter use back multiplexing technology, transfer 10M/100M Ethernet data by using multi E1 channels. Realize convert between 1 to 8 E1 channels and Ethernet interface. It can transmit signal of E1 channel to RJ45 interface point to point, realize the connection of E1 channel and Ethernet. It different from normal bridge , supporting 1 to 8 E1 channels customized configuration, auto detecting the number of E1 channels and use the available E1, allow some limiting transfer delay between different E1 channels. Single line speed is 1968Kbits/s, 8 channels can up to 15744Kbits/s. it can connect with Ethernet switch or hub when in 10/100Mbps full/half duplex mode, make use of mass E1 resource in telecommunication networks to expend the transfer distance and application field of Ethernet, is a suitable solution for broadband switch in of Ethernet. It can used in fields such as connecting LANs, connecting end offices, VOD, remote monitor, E1 interface of switches, etc.
Features
● Realizing the transparent transmission of Ethernet data via 1 to 8 E1 lines
● Providing 10/100Base-Tx&100Base-Fx interface in compliance with the protocol
● standard IEEE 802.3, providing 2 electronical Ethernet ports and one optical Ethernet port
● supporting the working mode of either full duplex or half-duplex.
● Able to transparently transmit the ultra-long frames (up to 1916 bytes) as defined in IEEE 802.1Q, supporting transparent transmission of VLAN frames.
● Providing an in-built dynamic Ethernet MAC address list (1024 addresses) with filtering function for local data frames.
● 128MBits large capacity cache memory and an in-built SDRAM controller, to adapt to various service requirements.
● E1 interface in compliance with ITU-T G.703, G.704 and G.823, not applicable for signaling time slot.
● E1 Support 75Ω/unbalance impedance or 120Ω/balance for order
● Allowing a clock drift up to 512UI in the transmission system, with significantly enhanced reliability.
● Providing availability detection and automatic troubleshooting for 1 to 8 E lines.
● Supporting E1 interface loop-back function and Ethernet loop-back function.
● Self-contained line alarm indication and output.
● Optional power supply, e.g. AC220V or DC-48V; optional mounting type, e.g. desktop or rack mounted.
● Power consumption: <10 W
|
E1 Interface
Line Rate: 2.048Mbps±50ppm
Line Code :HDB3
Interface Standard: ITU-T G.703
E1 Impedance: 75Ω(unbalance) or 120Ω(balance)
Connections : 75ohm DB37 adaptor or 120-ohm twisted-pair (RJ45)
Jitter tolerance : finer than G.742 and G.823
|
|
|
|
 |
 |
10/100Base-T Interface
Ports: 2*10/100Base-Tx and 1*100Base-Fx ports
Rate: 10/100M, full/duplex auto-negotiation
Protocol: Support IEEE 802.3,IEEE 802.1Q (VLAN)
Total Memory Sizes: 64MBits SDRAM
Physical interface: RJ45, support AUTO-MDIX
|
Power supply
working voltage range wide, good
anti-disturb and Isolation, work stable
option I – DC-48V,range DC-36V~DC-72C
option II – AC220V,range AC165V~AC240V
Power Consumption: <=10 Watts
environment condition
Operating temperature: 0C~+50 C
Storage temperature: -20 C~+70 C
Relative temperature:95% (uncondensed)
|
Dimension
440mm(L)X202mm(W)X43.5mm(H)
|
Application:
Ordering information
Related Products
